| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
arm64/fpsimd: ptrace: Fix SVE writes on !SME systems
When SVE is supported but SME is not supported, a ptrace write to the
NT_ARM_SVE regset can place the tracee into an invalid state where
(non-streaming) SVE register data is stored in FP_STATE_SVE format but
TIF_SVE is clear. This can result in a later warning from
fpsimd_restore_current_state(), e.g.
WARNING: CPU: 0 PID: 7214 at arch/arm64/kernel/fpsimd.c:383 fpsimd_restore_current_state+0x50c/0x748
When this happens, fpsimd_restore_current_state() will set TIF_SVE,
placing the task into the correct state. This occurs before any other
check of TIF_SVE can possibly occur, as other checks of TIF_SVE only
happen while the FPSIMD/SVE/SME state is live. Thus, aside from the
warning, there is no functional issue.
This bug was introduced during rework to error handling in commit:
9f8bf718f2923 ("arm64/fpsimd: ptrace: Gracefully handle errors")
... where the setting of TIF_SVE was moved into a block which is only
executed when system_supports_sme() is true.
Fix this by removing the system_supports_sme() check. This ensures that
TIF_SVE is set for (SVE-formatted) writes to NT_ARM_SVE, at the cost of
unconditionally manipulating the tracee's saved svcr value. The
manipulation of svcr is benign and inexpensive, and we already do
similar elsewhere (e.g. during signal handling), so I don't think it's
worth guarding this with system_supports_sme() checks.
Aside from the above, there is no functional change. The 'type' argument
to sve_set_common() is only set to ARM64_VEC_SME (in ssve_set())) when
system_supports_sme(), so the ARM64_VEC_SME case in the switch statement
is still unreachable when !system_supports_sme(). When
CONFIG_ARM64_SME=n, the only caller of sve_set_common() is sve_set(),
and the compiler can constant-fold for the case where type is
ARM64_VEC_SVE, removing the logic for other cases. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: Fix not set tty->port race condition
Revert commit bfc467db60b7 ("serial: remove redundant
tty_port_link_device()") because the tty_port_link_device() is not
redundant: the tty->port has to be confured before we call
uart_configure_port(), otherwise user-space can open console without TTY
linked to the driver.
This tty_port_link_device() was added explicitly to avoid this exact
issue in commit fb2b90014d78 ("tty: link tty and port before configuring
it as console"), so offending commit basically reverted the fix saying
it is redundant without addressing the actual race condition presented
there.
Reproducible always as tty->port warning on Qualcomm SoC with most of
devices disabled, so with very fast boot, and one serial device being
the console:
printk: legacy console [ttyMSM0] enabled
printk: legacy console [ttyMSM0] enabled
printk: legacy bootconsole [qcom_geni0] disabled
printk: legacy bootconsole [qcom_geni0] disabled
------------[ cut here ]------------
tty_init_dev: ttyMSM driver does not set tty->port. This would crash the kernel. Fix the driver!
WARNING: drivers/tty/tty_io.c:1414 at tty_init_dev.part.0+0x228/0x25c, CPU#2: systemd/1
Modules linked in: socinfo tcsrcc_eliza gcc_eliza sm3_ce fuse ipv6
CPU: 2 UID: 0 PID: 1 Comm: systemd Tainted: G S 6.19.0-rc4-next-20260108-00024-g2202f4d30aa8 #73 PREEMPT
Tainted: [S]=CPU_OUT_OF_SPEC
Hardware name: Qualcomm Technologies, Inc. Eliza (DT)
...
tty_init_dev.part.0 (drivers/tty/tty_io.c:1414 (discriminator 11)) (P)
tty_open (arch/arm64/include/asm/atomic_ll_sc.h:95 (discriminator 3) drivers/tty/tty_io.c:2073 (discriminator 3) drivers/tty/tty_io.c:2120 (discriminator 3))
chrdev_open (fs/char_dev.c:411)
do_dentry_open (fs/open.c:962)
vfs_open (fs/open.c:1094)
do_open (fs/namei.c:4634)
path_openat (fs/namei.c:4793)
do_filp_open (fs/namei.c:4820)
do_sys_openat2 (fs/open.c:1391 (discriminator 3))
...
Starting Network Name Resolution...
Apparently the flow with this small Yocto-based ramdisk user-space is:
driver (qcom_geni_serial.c): user-space:
============================ ===========
qcom_geni_serial_probe()
uart_add_one_port()
serial_core_register_port()
serial_core_add_one_port()
uart_configure_port()
register_console()
|
| open console
| ...
| tty_init_dev()
| driver->ports[idx] is NULL
|
tty_port_register_device_attr_serdev()
tty_port_link_device() <- set driver->ports[idx] |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: imx8m-blk-ctrl: Remove separate rst and clk mask for 8mq vpu
For i.MX8MQ platform, the ADB in the VPUMIX domain has no separate reset
and clock enable bits, but is ungated and reset together with the VPUs.
So we can't reset G1 or G2 separately, it may led to the system hang.
Remove rst_mask and clk_mask of imx8mq_vpu_blk_ctl_domain_data.
Let imx8mq_vpu_power_notifier() do really vpu reset. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: add missing ice_deinit_hw() in devlink reinit path
devlink-reload results in ice_init_hw failed error, and then removing
the ice driver causes a NULL pointer dereference.
[ +0.102213] ice 0000:ca:00.0: ice_init_hw failed: -16
...
[ +0.000001] Call Trace:
[ +0.000003] <TASK>
[ +0.000006] ice_unload+0x8f/0x100 [ice]
[ +0.000081] ice_remove+0xba/0x300 [ice]
Commit 1390b8b3d2be ("ice: remove duplicate call to ice_deinit_hw() on
error paths") removed ice_deinit_hw() from ice_deinit_dev(). As a result
ice_devlink_reinit_down() no longer calls ice_deinit_hw(), but
ice_devlink_reinit_up() still calls ice_init_hw(). Since the control
queues are not uninitialized, ice_init_hw() fails with -EBUSY.
Add ice_deinit_hw() to ice_devlink_reinit_down() to correspond with
ice_init_hw() in ice_devlink_reinit_up(). |
| In the Linux kernel, the following vulnerability has been resolved:
fou: Don't allow 0 for FOU_ATTR_IPPROTO.
fou_udp_recv() has the same problem mentioned in the previous
patch.
If FOU_ATTR_IPPROTO is set to 0, skb is not freed by
fou_udp_recv() nor "resubmit"-ted in ip_protocol_deliver_rcu().
Let's forbid 0 for FOU_ATTR_IPPROTO. |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: provide a net pointer to __skb_flow_dissect()
After 3cbf4ffba5ee ("net: plumb network namespace into __skb_flow_dissect")
we have to provide a net pointer to __skb_flow_dissect(),
either via skb->dev, skb->sk, or a user provided pointer.
In the following case, syzbot was able to cook a bare skb.
WARNING: net/core/flow_dissector.c:1131 at __skb_flow_dissect+0xb57/0x68b0 net/core/flow_dissector.c:1131, CPU#1: syz.2.1418/11053
Call Trace:
<TASK>
bond_flow_dissect drivers/net/bonding/bond_main.c:4093 [inline]
__bond_xmit_hash+0x2d7/0xba0 drivers/net/bonding/bond_main.c:4157
bond_xmit_hash_xdp drivers/net/bonding/bond_main.c:4208 [inline]
bond_xdp_xmit_3ad_xor_slave_get drivers/net/bonding/bond_main.c:5139 [inline]
bond_xdp_get_xmit_slave+0x1fd/0x710 drivers/net/bonding/bond_main.c:5515
xdp_master_redirect+0x13f/0x2c0 net/core/filter.c:4388
bpf_prog_run_xdp include/net/xdp.h:700 [inline]
bpf_test_run+0x6b2/0x7d0 net/bpf/test_run.c:421
bpf_prog_test_run_xdp+0x795/0x10e0 net/bpf/test_run.c:1390
bpf_prog_test_run+0x2c7/0x340 kernel/bpf/syscall.c:4703
__sys_bpf+0x562/0x860 kernel/bpf/syscall.c:6182
__do_sys_bpf kernel/bpf/syscall.c:6274 [inline]
__se_sys_bpf kernel/bpf/syscall.c:6272 [inline]
__x64_sys_bpf+0x7c/0x90 kernel/bpf/syscall.c:6272
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xec/0xf80 arch/x86/entry/syscall_64.c:94 |
| In the Linux kernel, the following vulnerability has been resolved:
l2tp: avoid one data-race in l2tp_tunnel_del_work()
We should read sk->sk_socket only when dealing with kernel sockets.
syzbot reported the following data-race:
BUG: KCSAN: data-race in l2tp_tunnel_del_work / sk_common_release
write to 0xffff88811c182b20 of 8 bytes by task 5365 on cpu 0:
sk_set_socket include/net/sock.h:2092 [inline]
sock_orphan include/net/sock.h:2118 [inline]
sk_common_release+0xae/0x230 net/core/sock.c:4003
udp_lib_close+0x15/0x20 include/net/udp.h:325
inet_release+0xce/0xf0 net/ipv4/af_inet.c:437
__sock_release net/socket.c:662 [inline]
sock_close+0x6b/0x150 net/socket.c:1455
__fput+0x29b/0x650 fs/file_table.c:468
____fput+0x1c/0x30 fs/file_table.c:496
task_work_run+0x131/0x1a0 kernel/task_work.c:233
resume_user_mode_work include/linux/resume_user_mode.h:50 [inline]
__exit_to_user_mode_loop kernel/entry/common.c:44 [inline]
exit_to_user_mode_loop+0x1fe/0x740 kernel/entry/common.c:75
__exit_to_user_mode_prepare include/linux/irq-entry-common.h:226 [inline]
syscall_exit_to_user_mode_prepare include/linux/irq-entry-common.h:256 [inline]
syscall_exit_to_user_mode_work include/linux/entry-common.h:159 [inline]
syscall_exit_to_user_mode include/linux/entry-common.h:194 [inline]
do_syscall_64+0x1e1/0x2b0 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x77/0x7f
read to 0xffff88811c182b20 of 8 bytes by task 827 on cpu 1:
l2tp_tunnel_del_work+0x2f/0x1a0 net/l2tp/l2tp_core.c:1418
process_one_work kernel/workqueue.c:3257 [inline]
process_scheduled_works+0x4ce/0x9d0 kernel/workqueue.c:3340
worker_thread+0x582/0x770 kernel/workqueue.c:3421
kthread+0x489/0x510 kernel/kthread.c:463
ret_from_fork+0x149/0x290 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246
value changed: 0xffff88811b818000 -> 0x0000000000000000 |
| In the Linux kernel, the following vulnerability has been resolved:
mISDN: annotate data-race around dev->work
dev->work can re read locklessly in mISDN_read()
and mISDN_poll(). Add READ_ONCE()/WRITE_ONCE() annotations.
BUG: KCSAN: data-race in mISDN_ioctl / mISDN_read
write to 0xffff88812d848280 of 4 bytes by task 10864 on cpu 1:
misdn_add_timer drivers/isdn/mISDN/timerdev.c:175 [inline]
mISDN_ioctl+0x2fb/0x550 drivers/isdn/mISDN/timerdev.c:233
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl+0xce/0x140 fs/ioctl.c:583
__x64_sys_ioctl+0x43/0x50 fs/ioctl.c:583
x64_sys_call+0x14b0/0x3000 arch/x86/include/generated/asm/syscalls_64.h:17
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xd8/0x2c0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
read to 0xffff88812d848280 of 4 bytes by task 10857 on cpu 0:
mISDN_read+0x1f2/0x470 drivers/isdn/mISDN/timerdev.c:112
do_loop_readv_writev fs/read_write.c:847 [inline]
vfs_readv+0x3fb/0x690 fs/read_write.c:1020
do_readv+0xe7/0x210 fs/read_write.c:1080
__do_sys_readv fs/read_write.c:1165 [inline]
__se_sys_readv fs/read_write.c:1162 [inline]
__x64_sys_readv+0x45/0x50 fs/read_write.c:1162
x64_sys_call+0x2831/0x3000 arch/x86/include/generated/asm/syscalls_64.h:20
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xd8/0x2c0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
value changed: 0x00000000 -> 0x00000001 |
| In the Linux kernel, the following vulnerability has been resolved:
uacce: fix cdev handling in the cleanup path
When cdev_device_add fails, it internally releases the cdev memory,
and if cdev_device_del is then executed, it will cause a hang error.
To fix it, we check the return value of cdev_device_add() and clear
uacce->cdev to avoid calling cdev_device_del in the uacce_remove. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: server: fix leak of active_num_conn in ksmbd_tcp_new_connection()
On kthread_run() failure in ksmbd_tcp_new_connection(), the transport is
freed via free_transport(), which does not decrement active_num_conn,
leaking this counter.
Replace free_transport() with ksmbd_tcp_disconnect(). |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: virtio - Add spinlock protection with virtqueue notification
When VM boots with one virtio-crypto PCI device and builtin backend,
run openssl benchmark command with multiple processes, such as
openssl speed -evp aes-128-cbc -engine afalg -seconds 10 -multi 32
openssl processes will hangup and there is error reported like this:
virtio_crypto virtio0: dataq.0:id 3 is not a head!
It seems that the data virtqueue need protection when it is handled
for virtio done notification. If the spinlock protection is added
in virtcrypto_done_task(), openssl benchmark with multiple processes
works well. |
| In the Linux kernel, the following vulnerability has been resolved:
migrate: correct lock ordering for hugetlb file folios
Syzbot has found a deadlock (analyzed by Lance Yang):
1) Task (5749): Holds folio_lock, then tries to acquire i_mmap_rwsem(read lock).
2) Task (5754): Holds i_mmap_rwsem(write lock), then tries to acquire
folio_lock.
migrate_pages()
-> migrate_hugetlbs()
-> unmap_and_move_huge_page() <- Takes folio_lock!
-> remove_migration_ptes()
-> __rmap_walk_file()
-> i_mmap_lock_read() <- Waits for i_mmap_rwsem(read lock)!
hugetlbfs_fallocate()
-> hugetlbfs_punch_hole() <- Takes i_mmap_rwsem(write lock)!
-> hugetlbfs_zero_partial_page()
-> filemap_lock_hugetlb_folio()
-> filemap_lock_folio()
-> __filemap_get_folio <- Waits for folio_lock!
The migration path is the one taking locks in the wrong order according to
the documentation at the top of mm/rmap.c. So expand the scope of the
existing i_mmap_lock to cover the calls to remove_migration_ptes() too.
This is (mostly) how it used to be after commit c0d0381ade79. That was
removed by 336bf30eb765 for both file & anon hugetlb pages when it should
only have been removed for anon hugetlb pages. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix bsg_done() causing double free
Kernel panic observed on system,
[5353358.825191] BUG: unable to handle page fault for address: ff5f5e897b024000
[5353358.825194] #PF: supervisor write access in kernel mode
[5353358.825195] #PF: error_code(0x0002) - not-present page
[5353358.825196] PGD 100006067 P4D 0
[5353358.825198] Oops: 0002 [#1] PREEMPT SMP NOPTI
[5353358.825200] CPU: 5 PID: 2132085 Comm: qlafwupdate.sub Kdump: loaded Tainted: G W L ------- --- 5.14.0-503.34.1.el9_5.x86_64 #1
[5353358.825203] Hardware name: HPE ProLiant DL360 Gen11/ProLiant DL360 Gen11, BIOS 2.44 01/17/2025
[5353358.825204] RIP: 0010:memcpy_erms+0x6/0x10
[5353358.825211] RSP: 0018:ff591da8f4f6b710 EFLAGS: 00010246
[5353358.825212] RAX: ff5f5e897b024000 RBX: 0000000000007090 RCX: 0000000000001000
[5353358.825213] RDX: 0000000000001000 RSI: ff591da8f4fed090 RDI: ff5f5e897b024000
[5353358.825214] RBP: 0000000000010000 R08: ff5f5e897b024000 R09: 0000000000000000
[5353358.825215] R10: ff46cf8c40517000 R11: 0000000000000001 R12: 0000000000008090
[5353358.825216] R13: ff591da8f4f6b720 R14: 0000000000001000 R15: 0000000000000000
[5353358.825218] FS: 00007f1e88d47740(0000) GS:ff46cf935f940000(0000) knlGS:0000000000000000
[5353358.825219] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[5353358.825220] CR2: ff5f5e897b024000 CR3: 0000000231532004 CR4: 0000000000771ef0
[5353358.825221] PKRU: 55555554
[5353358.825222] Call Trace:
[5353358.825223] <TASK>
[5353358.825224] ? show_trace_log_lvl+0x1c4/0x2df
[5353358.825229] ? show_trace_log_lvl+0x1c4/0x2df
[5353358.825232] ? sg_copy_buffer+0xc8/0x110
[5353358.825236] ? __die_body.cold+0x8/0xd
[5353358.825238] ? page_fault_oops+0x134/0x170
[5353358.825242] ? kernelmode_fixup_or_oops+0x84/0x110
[5353358.825244] ? exc_page_fault+0xa8/0x150
[5353358.825247] ? asm_exc_page_fault+0x22/0x30
[5353358.825252] ? memcpy_erms+0x6/0x10
[5353358.825253] sg_copy_buffer+0xc8/0x110
[5353358.825259] qla2x00_process_vendor_specific+0x652/0x1320 [qla2xxx]
[5353358.825317] qla24xx_bsg_request+0x1b2/0x2d0 [qla2xxx]
Most routines in qla_bsg.c call bsg_done() only for success cases.
However a few invoke it for failure case as well leading to a double
free. Validate before calling bsg_done(). |
| In the Linux kernel, the following vulnerability has been resolved:
Revert "f2fs: block cache/dio write during f2fs_enable_checkpoint()"
This reverts commit 196c81fdd438f7ac429d5639090a9816abb9760a.
Original patch may cause below deadlock, revert it.
write remount
- write_begin
- lock_page --- lock A
- prepare_write_begin
- f2fs_map_lock
- f2fs_enable_checkpoint
- down_write(cp_enable_rwsem) --- lock B
- sync_inode_sb
- writepages
- lock_page --- lock A
- down_read(cp_enable_rwsem) --- lock A |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid mapping wrong physical block for swapfile
Xiaolong Guo reported a f2fs bug in bugzilla [1]
[1] https://bugzilla.kernel.org/show_bug.cgi?id=220951
Quoted:
"When using stress-ng's swap stress test on F2FS filesystem with kernel 6.6+,
the system experiences data corruption leading to either:
1 dm-verity corruption errors and device reboot
2 F2FS node corruption errors and boot hangs
The issue occurs specifically when:
1 Using F2FS filesystem (ext4 is unaffected)
2 Swapfile size is less than F2FS section size (2MB)
3 Swapfile has fragmented physical layout (multiple non-contiguous extents)
4 Kernel version is 6.6+ (6.1 is unaffected)
The root cause is in check_swap_activate() function in fs/f2fs/data.c. When the
first extent of a small swapfile (< 2MB) is not aligned to section boundaries,
the function incorrectly treats it as the last extent, failing to map
subsequent extents. This results in incorrect swap_extent creation where only
the first extent is mapped, causing subsequent swap writes to overwrite wrong
physical locations (other files' data).
Steps to Reproduce
1 Setup a device with F2FS-formatted userdata partition
2 Compile stress-ng from https://github.com/ColinIanKing/stress-ng
3 Run swap stress test: (Android devices)
adb shell "cd /data/stressng; ./stress-ng-64 --metrics-brief --timeout 60
--swap 0"
Log:
1 Ftrace shows in kernel 6.6, only first extent is mapped during second
f2fs_map_blocks call in check_swap_activate():
stress-ng-swap-8990: f2fs_map_blocks: ino=11002, file offset=0, start
blkaddr=0x43143, len=0x1
(Only 4KB mapped, not the full swapfile)
2 in kernel 6.1, both extents are correctly mapped:
stress-ng-swap-5966: f2fs_map_blocks: ino=28011, file offset=0, start
blkaddr=0x13cd4, len=0x1
stress-ng-swap-5966: f2fs_map_blocks: ino=28011, file offset=1, start
blkaddr=0x60c84b, len=0xff
The problematic code is in check_swap_activate():
if ((pblock - SM_I(sbi)->main_blkaddr) % blks_per_sec ||
nr_pblocks % blks_per_sec ||
!f2fs_valid_pinned_area(sbi, pblock)) {
bool last_extent = false;
not_aligned++;
nr_pblocks = roundup(nr_pblocks, blks_per_sec);
if (cur_lblock + nr_pblocks > sis->max)
nr_pblocks -= blks_per_sec;
/* this extent is last one */
if (!nr_pblocks) {
nr_pblocks = last_lblock - cur_lblock;
last_extent = true;
}
ret = f2fs_migrate_blocks(inode, cur_lblock, nr_pblocks);
if (ret) {
if (ret == -ENOENT)
ret = -EINVAL;
goto out;
}
if (!last_extent)
goto retry;
}
When the first extent is unaligned and roundup(nr_pblocks, blks_per_sec)
exceeds sis->max, we subtract blks_per_sec resulting in nr_pblocks = 0. The
code then incorrectly assumes this is the last extent, sets nr_pblocks =
last_lblock - cur_lblock (entire swapfile), and performs migration. After
migration, it doesn't retry mapping, so subsequent extents are never processed.
"
In order to fix this issue, we need to lookup block mapping info after
we migrate all blocks in the tail of swapfile. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid UAF in f2fs_write_end_io()
As syzbot reported an use-after-free issue in f2fs_write_end_io().
It is caused by below race condition:
loop device umount
- worker_thread
- loop_process_work
- do_req_filebacked
- lo_rw_aio
- lo_rw_aio_complete
- blk_mq_end_request
- blk_update_request
- f2fs_write_end_io
- dec_page_count
- folio_end_writeback
- kill_f2fs_super
- kill_block_super
- f2fs_put_super
: free(sbi)
: get_pages(, F2FS_WB_CP_DATA)
accessed sbi which is freed
In kill_f2fs_super(), we will drop all page caches of f2fs inodes before
call free(sbi), it guarantee that all folios should end its writeback, so
it should be safe to access sbi before last folio_end_writeback().
Let's relocate ckpt thread wakeup flow before folio_end_writeback() to
resolve this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix out-of-bounds access in sysfs attribute read/write
Some f2fs sysfs attributes suffer from out-of-bounds memory access and
incorrect handling of integer values whose size is not 4 bytes.
For example:
vm:~# echo 65537 > /sys/fs/f2fs/vde/carve_out
vm:~# cat /sys/fs/f2fs/vde/carve_out
65537
vm:~# echo 4294967297 > /sys/fs/f2fs/vde/atgc_age_threshold
vm:~# cat /sys/fs/f2fs/vde/atgc_age_threshold
1
carve_out maps to {struct f2fs_sb_info}->carve_out, which is a 8-bit
integer. However, the sysfs interface allows setting it to a value
larger than 255, resulting in an out-of-range update.
atgc_age_threshold maps to {struct atgc_management}->age_threshold,
which is a 64-bit integer, but its sysfs interface cannot correctly set
values larger than UINT_MAX.
The root causes are:
1. __sbi_store() treats all default values as unsigned int, which
prevents updating integers larger than 4 bytes and causes out-of-bounds
writes for integers smaller than 4 bytes.
2. f2fs_sbi_show() also assumes all default values are unsigned int,
leading to out-of-bounds reads and incorrect access to integers larger
than 4 bytes.
This patch introduces {struct f2fs_attr}->size to record the actual size
of the integer associated with each sysfs attribute. With this
information, sysfs read and write operations can correctly access and
update values according to their real data size, avoiding memory
corruption and truncation. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix dead lock while flushing management frames
Commit [1] converted the management transmission work item into a
wiphy work. Since a wiphy work can only run under wiphy lock
protection, a race condition happens in below scenario:
1. a management frame is queued for transmission.
2. ath12k_mac_op_flush() gets called to flush pending frames associated
with the hardware (i.e, vif being NULL). Then in ath12k_mac_flush()
the process waits for the transmission done.
3. Since wiphy lock has been taken by the flush process, the transmission
work item has no chance to run, hence the dead lock.
>From user view, this dead lock results in below issue:
wlp8s0: authenticate with xxxxxx (local address=xxxxxx)
wlp8s0: send auth to xxxxxx (try 1/3)
wlp8s0: authenticate with xxxxxx (local address=xxxxxx)
wlp8s0: send auth to xxxxxx (try 1/3)
wlp8s0: authenticated
wlp8s0: associate with xxxxxx (try 1/3)
wlp8s0: aborting association with xxxxxx by local choice (Reason: 3=DEAUTH_LEAVING)
ath12k_pci 0000:08:00.0: failed to flush mgmt transmit queue, mgmt pkts pending 1
The dead lock can be avoided by invoking wiphy_work_flush() to proactively
run the queued work item. Note actually it is already present in
ath12k_mac_op_flush(), however it does not protect the case where vif
being NULL. Hence move it ahead to cover this case as well.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3 |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: hp-bioscfg: Fix kobject warnings for empty attribute names
The hp-bioscfg driver attempts to register kobjects with empty names when
the HP BIOS returns attributes with empty name strings. This causes
multiple kernel warnings:
kobject: (00000000135fb5e6): attempted to be registered with empty name!
WARNING: CPU: 14 PID: 3336 at lib/kobject.c:219 kobject_add_internal+0x2eb/0x310
Add validation in hp_init_bios_buffer_attribute() to check if the
attribute name is empty after parsing it from the WMI buffer. If empty,
log a debug message and skip registration of that attribute, allowing the
module to continue processing other valid attributes. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix early read unlock of page with EOF in middle
The read result collection for buffered reads seems to run ahead of the
completion of subrequests under some circumstances, as can be seen in the
following log snippet:
9p_client_res: client 18446612686390831168 response P9_TREAD tag 0 err 0
...
netfs_sreq: R=00001b55[1] DOWN TERM f=192 s=0 5fb2/5fb2 s=5 e=0
...
netfs_collect_folio: R=00001b55 ix=00004 r=4000-5000 t=4000/5fb2
netfs_folio: i=157f3 ix=00004-00004 read-done
netfs_folio: i=157f3 ix=00004-00004 read-unlock
netfs_collect_folio: R=00001b55 ix=00005 r=5000-5fb2 t=5000/5fb2
netfs_folio: i=157f3 ix=00005-00005 read-done
netfs_folio: i=157f3 ix=00005-00005 read-unlock
...
netfs_collect_stream: R=00001b55[0:] cto=5fb2 frn=ffffffff
netfs_collect_state: R=00001b55 col=5fb2 cln=6000 n=c
netfs_collect_stream: R=00001b55[0:] cto=5fb2 frn=ffffffff
netfs_collect_state: R=00001b55 col=5fb2 cln=6000 n=8
...
netfs_sreq: R=00001b55[2] ZERO SUBMT f=000 s=5fb2 0/4e s=0 e=0
netfs_sreq: R=00001b55[2] ZERO TERM f=102 s=5fb2 4e/4e s=5 e=0
The 'cto=5fb2' indicates the collected file pos we've collected results to
so far - but we still have 0x4e more bytes to go - so we shouldn't have
collected folio ix=00005 yet. The 'ZERO' subreq that clears the tail
happens after we unlock the folio, allowing the application to see the
uncleared tail through mmap.
The problem is that netfs_read_unlock_folios() will unlock a folio in which
the amount of read results collected hits EOF position - but the ZERO
subreq lies beyond that and so happens after.
Fix this by changing the end check to always be the end of the folio and
never the end of the file.
In the future, I should look at clearing to the end of the folio here rather
than adding a ZERO subreq to do this. On the other hand, the ZERO subreq can
run in parallel with an async READ subreq. Further, the ZERO subreq may still
be necessary to, say, handle extents in a ceph file that don't have any
backing store and are thus implicitly all zeros.
This can be reproduced by creating a file, the size of which doesn't align
to a page boundary, e.g. 24998 (0x5fb2) bytes and then doing something
like:
xfs_io -c "mmap -r 0 0x6000" -c "madvise -d 0 0x6000" \
-c "mread -v 0 0x6000" /xfstest.test/x
The last 0x4e bytes should all be 00, but if the tail hasn't been cleared
yet, you may see rubbish there. This can be reproduced with kafs by
modifying the kernel to disable the call to netfs_read_subreq_progress()
and to stop afs_issue_read() from doing the async call for NETFS_READAHEAD.
Reproduction can be made easier by inserting an mdelay(100) in
netfs_issue_read() for the ZERO-subreq case.
AFS and CIFS are normally unlikely to show this as they dispatch READ ops
asynchronously, which allows the ZERO-subreq to finish first. 9P's READ op is
completely synchronous, so the ZERO-subreq will always happen after. It isn't
seen all the time, though, because the collection may be done in a worker
thread. |
