| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| An MS-MPC or MS-MIC Service PIC may crash when large fragmented packets are passed through an Application Layer Gateway (ALG). Repeated crashes of the Service PC can result in an extended denial of service condition. The issue can be seen only if NAT or stateful-firewall rules are configured with ALGs enabled. This issue was caused by the code change for PR 1182910 in Junos OS 14.1X55-D30, 14.1X55-D35, 14.2R7, 15.1R5, and 16.1R2. No other versions of Junos OS and no other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS on MX platforms running: 14.1X55 from 14.1X55-D30 to releases prior to 14.1X55-D35; 14.2R from 14.2R7 to releases prior to 14.2R7-S4, 14.2R8; 15.1R from 15.1R5 to releases prior to 15.1R5-S2, 15.1R6; 16.1R from 16.1R2 to releases prior to 16.1R3-S2, 16.1R4. |
| A persistent cross site scripting vulnerability in NetScreen WebUI of Juniper Networks Juniper NetScreen Firewall+VPN running ScreenOS allows a user with the 'security' role to inject HTML/JavaScript content into the management session of other users including the administrator. This enables the lower-privileged user to effectively execute commands with the permissions of an administrator. This issue affects Juniper Networks ScreenOS 6.3.0 releases prior to 6.3.0r24 on SSG Series. No other Juniper Networks products or platforms are affected by this issue. |
| On Juniper Networks Junos OS 15.1 releases from 15.1R3 to 15.1R4, 16.1 prior to 16.1R3, on M/MX platforms where Enhanced Subscriber Management for DHCPv6 subscribers is configured, a vulnerability in processing IPv6 ND packets originating from subscribers and destined to M/MX series routers can result in a PFE (Packet Forwarding Engine) hang or crash. |
| An information leak vulnerability in Juniper Networks NorthStar Controller Application prior to version 2.1.0 Service Pack 1 may allow a network-based malicious attacker to perform a man-in-the-middle attack, thereby stealing authentic credentials from encrypted paths which are easily decrypted, and subsequently gain complete control of the system. |
| An insufficient authentication vulnerability on platforms where Junos OS instances are run in a virtualized environment, may allow unprivileged users on the Junos OS instance to gain access to the host operating environment, and thus escalate privileges. Affected releases are Juniper Networks Junos OS 14.1X53 prior to 14.1X53-D40 on QFX5110, QFX5200, QFX10002, QFX10008, QFX10016, EX4600 and NFX250; 15.1 prior to 15.1R5 on EX4600; 15.1X49 prior to 15.1X49-D70 on vSRX, SRX1500, SRX4100, SRX4200; 16.1 prior to 16.1R2 on EX4600, ACX5000 series. This issue does not affect vMX. No other Juniper Networks products or platforms are affected by this issue. |
| A vulnerability in a specific loopback filter action command, processed in a specific logical order of operation, in a running configuration of Juniper Networks Junos OS, allows an attacker with CLI access and the ability to initiate remote sessions to the loopback interface with the defined action, to hang the kernel. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D55; 12.3X48 prior to 12.3X48-D35; 14.1 prior to 14.1R8-S4, 14.1R9; 14.1X53 prior to 14.1X53-D40; 14.2 prior to 14.2R4-S9, 14.2R7-S8, 14.2R8; 15.1 prior to 15.1F5-S3, 15.1F6, 15.1R4; 15.1X49 prior to 15.1X49-D60; 15.1X53 prior to 15.1X53-D47; 16.1 prior to 16.1R2. No other Juniper Networks products or platforms are affected by this issue. |
| A routine within an internal Junos OS sockets library is vulnerable to a buffer overflow. Malicious exploitation of this issue may lead to a denial of service (kernel panic) or be leveraged as a privilege escalation through local code execution. The routines are only accessible via programs running on the device itself, and veriexec restricts arbitrary programs from running on Junos OS. There are no known exploit vectors utilizing signed binaries shipped with Junos OS itself. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D67; 12.3X48 prior to 12.3X48-D51, 12.3X48-D55; 13.3 prior to 13.3R10-S2; 14.1 prior to 14.1R2-S10, 14.1R8-S4, 14.1R9; 14.1X50 prior to 14.1X50-D185; 14.1X53 prior to 14.1X53-D122, 14.1X53-D45, 14.1X53-D50; 14.2 prior to 14.2R4-S9, 14.2R7-S7, 14.2R8; 15.1 prior to 15.1F2-S18, 15.1F6-S7, 15.1R4-S8, 15.1R5-S5, 15.1R6-S1, 15.1R7; 15.1X49 prior to 15.1X49-D100; 15.1X53 prior to 15.1X53-D231, 15.1X53-D47, 15.1X53-D48, 15.1X53-D57, 15.1X53-D64, 15.1X53-D70; 16.1 prior to 16.1R3-S4, 16.1R4-S3, 16.1R4-S4, 16.1R5; 16.2 prior to 16.2R2; 17.1 prior to 17.1R1-S3, 17.1R2; 17.2 prior to 17.2R1-S1, 17.2R2; 17.2X75 prior to 17.2X75-D30. No other Juniper Networks products or platforms are affected by this issue. |
| On Juniper Networks products or platforms running Junos OS 11.4 prior to 11.4R13-S3, 12.1X46 prior to 12.1X46-D60, 12.3 prior to 12.3R12-S2 or 12.3R13, 12.3X48 prior to 12.3X48-D40, 13.2X51 prior to 13.2X51-D40, 13.3 prior to 13.3R10, 14.1 prior to 14.1R8, 14.1X53 prior to 14.1X53-D12 or 14.1X53-D35, 14.1X55 prior to 14.1X55-D35, 14.2 prior to 14.2R7, 15.1 prior to 15.1F6 or 15.1R3, 15.1X49 prior to 15.1X49-D60, 15.1X53 prior to 15.1X53-D30 and DHCPv6 enabled, when a crafted DHCPv6 packet is received from a subscriber, jdhcpd daemon crashes and restarts. Repeated crashes of the jdhcpd process may constitute an extended denial of service condition for subscribers attempting to obtain IPv6 addresses. |
| On Juniper Networks products or platforms running Junos OS 12.1X46 prior to 12.1X46-D55, 12.1X47 prior to 12.1X47-D45, 12.3R13 prior to 12.3R13, 12.3X48 prior to 12.3X48-D35, 13.3 prior to 13.3R10, 14.1 prior to 14.1R8, 14.1X53 prior to 14.1X53-D40, 14.1X55 prior to 14.1X55-D35, 14.2 prior to 14.2R6, 15.1 prior to 15.1F2 or 15.1R1, 15.1X49 prior to 15.1X49-D20 where the BGP add-path feature is enabled with 'send' option or with both 'send' and 'receive' options, a network based attacker can cause the Junos OS rpd daemon to crash and restart. Repeated crashes of the rpd daemon can result in an extended denial of service condition. |
| An XML External Entity Injection vulnerability in Juniper Networks Junos Space versions prior to 16.1R1 may allow an authenticated user to read arbitrary files on the device. |
| Juniper Networks Junos OS on SRX series devices do not verify the HTTPS server certificate before downloading anti-virus updates. This may allow a man-in-the-middle attacker to inject bogus signatures to cause service disruptions or make the device not detect certain types of attacks. Affected Junos OS releases are: 12.1X46 prior to 12.1X46-D71; 12.3X48 prior to 12.3X48-D55; 15.1X49 prior to 15.1X49-D110; |
| When Express Path (formerly known as service offloading) is configured on Juniper Networks SRX1400, SRX3400, SRX3600, SRX5400, SRX5600, SRX5800 in high availability cluster configuration mode, certain multicast packets might cause the flowd process to crash, halting or interrupting traffic from flowing through the device and triggering RG1+ (data-plane) fail-over to the secondary node. Repeated crashes of the flowd process may constitute an extended denial of service condition. This service is not enabled by default and is only supported in high-end SRX platforms. Affected releases are Juniper Networks Junos OS 12.3X48 prior to 12.3X48-D45, 15.1X49 prior to 15.1X49-D80 on SRX1400, SRX3400, SRX3600, SRX5400, SRX5600, SRX5800. |
| A denial of service vulnerability in rpd daemon of Juniper Networks Junos OS allows a malformed MPLS ping packet to crash the rpd daemon if MPLS OAM is configured. Repeated crashes of the rpd daemon can result in an extended denial of service condition for the device. The affected releases are Junos OS 12.3X48 prior to 12.3X48-D50, 12.3X48-D55; 13.3 prior to 13.3R10; 14.1 prior to 14.1R4-S13, 14.1R8-S3, 14.1R9; 14.1X53 prior to 14.1X53-D42, 14.1X53-D50; 14.2 prior to 14.2R4-S8, 14.2R7-S6, 14.2R8; 15.1 prior to 15.1F2-S14, 15.1F5-S7, 15.1F6-S4, 15.1F7, 15.1R4-S7, 15.1R5-S1, 15.1R6; 15.1X49 prior to 15.1X49-D100; 15.1X53 prior to 15.1X53-D105, 15.1X53-D47, 15.1X53-D62, 15.1X53-D70; 16.1 prior to 16.1R3-S3, 16.1R4. No other Juniper Networks products or platforms are affected by this issue. |
| The Juniper Enhanced jdhcpd daemon may experience high CPU utilization, or crash and restart upon receipt of an invalid IPv6 UDP packet. Both high CPU utilization and repeated crashes of the jdhcpd daemon can result in a denial of service as DHCP service is interrupted. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 14.1X53 prior to 14.1X53-D12, 14.1X53-D38, 14.1X53-D40 on QFX, EX, QFabric System; 15.1 prior to 15.1F2-S18, 15.1R4 on all products and platforms; 15.1X49 prior to 15.1X49-D80 on SRX; 15.1X53 prior to 15.1X53-D51, 15.1X53-D60 on NFX, QFX, EX. |
| On Juniper Networks devices running Junos OS affected versions and with LDP enabled, a specific LDP packet destined to the RE (Routing Engine) will consume a small amount of the memory allocated for the rpd (routing protocol daemon) process. Over time, repeatedly receiving this type of LDP packet(s) will cause the memory to exhaust and the rpd process to crash and restart. It is not possible to free up the memory that has been consumed without restarting the rpd process. This issue affects Junos OS based devices with either IPv4 or IPv6 LDP enabled via the [protocols ldp] configuration (the native IPv6 support for LDP is available in Junos OS 16.1 and higher). The interface on which the packet arrives needs to have LDP enabled. The affected Junos versions are: 13.3 prior to 13.3R10; 14.1 prior to 14.1R8; 14.2 prior to 14.2R7-S6 or 14.2R8; 15.1 prior to 15.1F2-S14, 15.1F6-S4, 15.1F7, 15.1R4-S7, 15.1R5; 15.1X49 before 15.1X49-D70; 15.1X53 before 15.1X53-D230, 15.1X53-D63, 15.1X53-D70; 16.1 before 16.1R2. 16.2R1 and all subsequent releases have a resolution for this vulnerability. |
| A vulnerability in the pluggable authentication module (PAM) of Juniper Networks Junos OS may allow an unauthenticated network based attacker to potentially execute arbitrary code or crash daemons such as telnetd or sshd that make use of PAM. Affected Juniper Networks Junos OS releases are: 14.1 from 14.1R5 prior to 14.1R8-S4, 14.1R9; 14.1X53 prior to 14.1X53-D50 on EX and QFX series; 14.2 from 14.2R3 prior to 14.2R7-S8, 14.2R8; No other Junos OS releases are affected by this issue. No other Juniper Networks products are affected by this issue. |
| Receipt of a malformed BGP OPEN message may cause the routing protocol daemon (rpd) process to crash and restart. By continuously sending specially crafted BGP OPEN messages, an attacker can repeatedly crash the rpd process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 12.3 prior to 12.3R12-S4, 12.3R13, 12.3R3-S4; 12.3X48 prior to 12.3X48-D50; 13.3 prior to 13.3R4-S11, 13.3R10; 14.1 prior to 14.1R8-S3, 14.1R9; 14.1X53 prior to 14.1X53-D40; 14.1X55 prior to 14.1X55-D35; 14.2 prior to 14.2R4-S7, 14.2R6-S4, 14.2R7; 15.1 prior to 15.1F2-S11, 15.1F4-S1-J1, 15.1F5-S3, 15.1F6, 15.1R4; 15.1X49 prior to 15.1X49-D100; 15.1X53 prior to 15.1X53-D33, 15.1X53-D50. |
| If extended statistics are enabled via 'set chassis extended-statistics', when executing any operation that fetches interface statistics, including but not limited to SNMP GET requests, the pfem process or the FPC may crash and restart. Repeated crashes of PFE processing can result in an extended denial of service condition. This issue only affects the following platforms: (1) EX2200, EX3300, XRE200 (2) MX Series routers with MPC7E/8E/9E PFEs installed, and only if 'extended-statistics' are enabled under the [edit chassis] configuration. Affected releases are Juniper Networks Junos OS 14.1 prior to 14.1R8-S5, 14.1R9 on MX Series; 14.1X53 prior to 14.1X53-D46, 14.1X53-D50 on EX2200, EX3300, XRE200; 14.2 prior to 14.2R7-S9, 14.2R8 on MX Series; 15.1 prior to 15.1F5-S8, 15.1F6-S8, 15.1R5-S3, 15.1R6 on MX Series; 16.1 prior to 16.1R4-S5, 16.1R5, 16.1R6 on MX Series; 16.1X65 prior to 16.1X65-D45 on EX2200, EX3300, XRE200; 16.2 prior to 16.2R2-S1, 16.2R3 on MX Series; 17.1 prior to 17.1R2-S2, 17.1R3 on MX Series; 17.2 prior to 17.2R1-S3, 17.2R2 on MX Series; 17.2X75 prior to 17.2X75-D50 on MX Series; 17.3 prior to 17.3R1-S1, 17.3R2 on MX Series. No other Juniper Networks products or platforms are affected by this issue. |
| A reflected cross site scripting vulnerability in NetScreen WebUI of Juniper Networks Juniper NetScreen Firewall+VPN running ScreenOS allows a network based attacker to inject HTML/JavaScript content into the management session of other users including the administrator. This enables the attacker to effectively execute commands with the permissions of an administrator. This issue affects Juniper Networks ScreenOS 6.3.0 releases prior to 6.3.0r24 on SSG Series. No other Juniper Networks products or platforms are affected by this issue. |
| A persistent cross site scripting vulnerability in NetScreen WebUI of Juniper Networks Juniper NetScreen Firewall+VPN running ScreenOS allows a user with the 'security' role to inject HTML/JavaScript content into the management session of other users including the administrator. This enables the lower-privileged user to effectively execute commands with the permissions of an administrator. This issue affects Juniper Networks ScreenOS 6.3.0 releases prior to 6.3.0r24 on SSG Series. No other Juniper Networks products or platforms are affected by this issue. |
